Shop

This is a wonderful Martin 0-21, but with “the best of both worlds”: the light build of 1924– combined with 1930’s robust, “braced for steel” construction. It left the factory in 1924, but it went back to Martin in 1934 for a neck set, new belly bridge, and to get set up fully for steel strings. Details below.

• All original finish
• Original 1934 bridge, and bridge plate from Martin Factory
• Original saddle
• Original “arrowhead” design tuners. The first Waverly tuners showed up in 1924/25 and remained until after the war. The arrowhead design, seen here on the tuner plates, showed up also in 1924, still with the shafts placed underneath the gears / string posts.
• Crack free (there is one cleat inside guitar, on upper bout, back. There is no visible crack that goes through wood to inside, just a tiny finish crack on outside. No doubt the Martin luthier place the cleat there in 1934 as a preventative measure (that worked).
• The combination of the original thin-profile neck, with the braced-for-steel modifications by Martin factory in 1934, make for a very robust guitar– you can play it hard and it holds up and projects like a 30’s Martin.
• Sold by Martin factory and shipped to Rudolph Wurlitzer Co. in Chicago on March 18, 1924. (This guitar does not have “Wulitzer” stamps, rather the normal CF Martin Stamps in all the correct places. This is consistent with Martin/Wurlitzer timetable in “Martin Guitars: A Technical Reference” by Johnston and Boak, 2009, p. 248.)
• June 20, 1933: the owner wrote to Martin that instrument needed a neck set and the bridge was “adrift”. Martin replied on June 23 that the normal guarantee would probably cover this work.
• Owner sent the guitar to Martin on July 3, 1934. Martin reported back to owner on July 16 that readjusting the neck and regluing the bridge would be covered by the warranty, Martin also offered a “new” bridge (meaning belly bridge) for $1.50. Martin also said that some binding could be reglued and repaired for $3.00.
• Work done at Martin, July 1934. The luthier at Martin replaced the bridge with a 1934 spec ebony belly bridge, and replaced the bridge plate with a perfect, tucked, small maple bridge plate. Martin luthier signs underside of spruce top: "7-25-1934”, and put his initials (“W.T.W.”), right by the edge of the X-brace to the top/upper bout. Of course, the back was taken off the guitar to do the above work. But being perfectly done at Martin factory in 1934, there are no visible signs of that– back binding is perfect.
• Total repair bill from Martin factory in 1934: $4.50. Paid by check, and Martin return ships the 0-21 to owner on August 15th, 1934.

The 21 model is, of course, the cousin to the 28. Same combination of brazilian rosewood back and sides, and Adirondack spruce top, and ebony bridge and fingerboard. 1930’s 12 fret Martin 0-21’s are very rare. There was only one made in 1934. Between 1932 and 1939– the entire “golden age” at Martin, there were less than 100 made.

The Larson Brothers need little introduction to the world’s top players and collectors, and they are very different instruments from the Martin and Gibson instruments that dominated the 1920’s and 30’s by their shear numbers. Larson instruments are rising in value rapidly, as they never produced the kind of volume that Martin much less Gibson produced in those decades, and they are now recognized for their magnificent workmanship and tone. The now legendary Chicago-based Larson brothers, August and Carl, did not make instruments with a “Larson” label. All of their instruments were branded and marketed for Stahl, Maurer, Prairie State, Euphonon, Dyer, Bruno, and a few more. Yet every one of their instruments has their unmistakable trademarks. And their unmistakable tone. This exquisitely beautiful, 100% original Larson Mandolin was made at the very height of the Larson legacy– when they were making their finest instruments. It has all of the Larson trademarks that set apart the best Larsons, including “built under tension” design, and Larson’s classic “ebony under the binding” on the neck. Every part of this instrument is 100% original. And its crack-free– save for two tiny dryness finish cracks near center of back, of about two inches each.

• 100% original finish, everywhere
• Scale length: 13 inches
• Nut width: 1 1/8 inches
• Serial number: 38764

This particular model, is one of the high end Larson models, a presentation grade instrument, with its Abalone trim, elaborate inlays on headstock, and fretboard, and exquisite Brazilian rosewood. Tone: think of the best Brazilian rosewood instruments, but add more sustain. It vibrates in your hands, and the tone, because of Larson’s patented “built under tension” design, is thought of by players and collectors as being both unique and delivering probably the most sustain you’ll get from any instrument. If you’ve never played a Larson brothers mandolin or guitar, be prepared to be shocked by the brilliant, shimmering tone, the sustain that goes on and on, and the harmonic overtones– that nothing but a Larson achieves. This Larson-built mandolin is identical to the one in the famous Hank Risan collection, the Museum of the Musical Instrument (www.themomi.org). The MOMI houses one of the best collections of twentieth century American instruments– and their collection of Larson brothers instruments is the best collection in the world, choosing only the best examples. The Larson/Stahl mandolin in that collection, identical to this one save a slightly different bridge, can be seen at: http://www.themomi.org/museum/roaring20s/c.1930_Stahl_Mandolin.html